This product is handmade in Europe and can take up to eight weeks to arrive. No returns or exchanges accepted.
What This Is
A custom-sewn leather e-brake boot for your 2005-12 BMW 3-Series. It replaces the factory boot and installs on your factory frame or trim. It is not a complete e-brake assembly.
What's Included
- Included: 1 leather e-brake boot, cut and sewn to order.
- Not included: e-brake handle, trim or hardware. You reuse your factory parts.
Before You Order
- Fits 2005-12 BMW 3-Series.
- It's made to order, so it can take up to 8 weeks to arrive and can't be returned or exchanged. Please double-check your year, fitment, and colors before ordering.
- International shipping: every piece ships from Poland, so a $15 international shipping charge applies to each item at checkout.
Installation
Difficulty: Moderate | Tools: screwdrivers, basic hand tools, glue or a stapler depending on your frame
You'll remove the e-brake trim, move the new boot onto your factory frame, and reinstall.
▼ Click to Open / Close Step-by-Step Installation Guide (7 Steps)
Step 1. The car has to be completely off during this procedure, and secured against rolling away. Pull upwards on the mounting points on the bottom of the boot, there is an integrated frame that will yield if you wiggle it (it's flexible to a point). To remove the shift knob, pull it upwards. Make sure to brace yourself so that you don't pull it too hard, it's best done while seated in either seat using just your forearms with the elbows braced on your thighs and center armrest. The picture shows the connector providing lighting of the shift knob. The connector is also connected to the side of the shifter assembly with the visible clip. Use a small flat-head screwdriver to push the center part of the clip left. The clip will disengage and you will be able to push the whole connector down (to push it out of the bracket that's holding it) and out.
Step 2. Squeeze the sides of the upper part of the connector to make the shift knob part release from the part of the wiring harness that goes back into the center console.
Step 3. Use an x-acto knife to cut the stock boot right under the shift knob. It's easy to do around the front and sides of the knob, as there is a plastic tube that makes it easy to just cut without worrying (worst case you will scratch an invisible piece of plastic). The rear is more tricky as the harness is exposed. Therefore cut the front and sides first, pull the harness out of the boot as pictured, insert the knife between the remaining leather and harness and cut all the way through. It's fine if a little old leather remains on the rear (harness) side of the bottom of the shift knob. That is fine.
Step 4. Glue the new boot on the shifter frame after removing it from the stock boot. It's the same procedure as for the manual (explained earlier in this write-up). Make sure the alignment is correct and that the glue settles well before proceeding. Once the frame is solid with the new boot, flip the boot inside out and insert the harness from above as pictured.
Step 5. Push the shift knob into the boot as far as it will go. Ideally you will want the bottom of the knob to be even, or almost even, with the top edge of the boot.
Step 6. Use a zip-tie to hold them together. Make the zip-tie tight.
Step 7. Flip the boot back out. This requires some dexterity. What helps is holding the zip-tied part of the assembly with one hand and pushing down with the other. If you aren't careful you will push the zip-tie off the knob and will have to get back to previous steps to redo it. Make sure you get it right before you run out of zip-ties.:) Reinstall the harness and clip the harness to the shifter. Lower the assembly over the shifter and push the shift knob on first, then clip the bottom frame until it holds. AUTO SHIFT BOOT installation below.
Leather care: apply a leather conditioner with UV protection every 4-6 weeks to keep it from drying out and cracking.
Options & Pricing
Choose your material, colors, and stitching color in the options above. Add-on prices are added in the cart.
Material
- Regular Leather
- Perforated Leather
- Faux Alcantara
- Carbon Fiber Vinyl
Two-tone: choose a second color in the options above.
Style
- Quadruple Thread +$9
Quadruple stitching color applies to the outer lines of thread.
Frequently Asked Questions
Q: Is my personal information kept private? Is it safe to use my credit card?
A: Yes, your personal information is kept private and it is safe to use your credit card.
Q: How much will shipping cost?
A: Unfortunately, the cost of shipping is a real expense. Our goal is to minimize your shipping costs. Shipping is calculated at checkout based on the items in your cart and will be displayed prior to you placing an order. Please note that oversized items may be subject to additional charges, which will be noted on the product page.
Q: How do I track my order?
A: Once your order ships, you will receive a tracking notification via email.
Q: Can someone outside of the United States place an order?
A: Yes, we are happy to provide worldwide service for our customers. Your shipping charges will be calculated during the checkout process. Customs and duty fees are the responsibility of the buyer.